Skroutz.cy

Optum ENC28J60 Ethernet Shield for Arduino for Arduino Nano v3

50 € coupon for your next purchase! + 1 offer for you!

Arduino

Optum ENC28J60 Ethernet Shield for Arduino for Arduino Nano v3

The Optum ENC28J60 Ethernet shield connects an Arduino Nano board to the internet. It uses the Microchip ENC28J60 Ethernet controller and can operate as a server or client.

  • Type: Shield
  • Board model:...

The Optum ENC28J60 Ethernet shield connects an Arduino Nano board to the internet. It uses the Microchip ENC28J60 Ethernet controller and can operate as a server or client.

  • Type: Shield
  • Board model: Nano
  • Ethernet controller: Microchip ENC28J60
  • Operating mode: Server or client
  • Connection: Plugs directly into the board, no soldering required
  • Library and...
See Description & Specifications See Description & Specifications
17 36 €
You earn a 50 € next purchase coupon
with an order over 200 €

Deals & Benefits

Κέρδισε 50€ κουπόνι!

Κάνε μία παραγγελία από 200€ έως 600€ έως 18/11 και κέρδισε κουπόνι 50€ για την επόμενη παραγγελία σου άνω των 300€.

Μην ξεχνάς ότι μπορείς να κερδίσεις έως 2 κουπόνια συνολικής αξίας 150€ για να κάνεις τις Black Friday αγορές σου ακόμα πιο συμφέρουσες!

  • H προωθητική ενέργεια ισχύει για μία (1) παραγγελία συνολικής αξίας προϊόντων από 200€ έως 600€ μέσω της Υπηρεσίας “Αγορά μέσω Skroutz” μεταξύ 9/11 00:01 έως και 18/11 23:59 με διεύθυνση αποστολής στην Κύπρο.
  • Το κουπόνι 50€ αποδίδεται αμέσως μετά την παράδοση της παραγγελίας συμμετοχής στην προωθητική ενέργεια, θα έχει διάρκεια 30 ημερών και θα είναι εξαργυρώσιμο σε μία παραγγελία άνω των 300€.

Terms & conditions apply
You earn a 100 € next purchase coupon
with an order over 600 €

Deals & Benefits

Κέρδισε 100€ κουπόνι!

Κάνε μία παραγγελία άνω των 600€ έως 18/11 και κέρδισε κουπόνι 100€ για την επόμενη παραγγελία σου άνω των 400€.

Μην ξεχνάς ότι μπορείς να κερδίσεις έως 2 κουπόνια συνολικής αξίας 150€ για να κάνεις τις Black Friday αγορές σου ακόμα πιο συμφέρουσες!

  • H προωθητική ενέργεια ισχύει για μία (1) παραγγελία συνολικής αξίας προϊόντων άνω των 600€ μέσω της Υπηρεσίας “Αγορά μέσω Skroutz” μεταξύ 9/11 00:01 έως και 18/11 23:59 με διεύθυνση αποστολής στην Κύπρο.
  • Το κουπόνι 100€ αποδίδεται αμέσως μετά την παράδοση της παραγγελίας συμμετοχής στην προωθητική ενέργεια, θα έχει διάρκεια 30 ημέρες και θα είναι εξαργυρώσιμο σε μία παραγγελία άνω των 400€.

Terms & conditions apply
Delivery Friday, 13 November
4,50 € shipping cost
Sent from Greece
From Top Electronics 4.9 (40)
4.9 (40 reviews)
Greece
2 pieces
See Microelectronics on the page of Top Electronics

Shop selection criteria

Why do we recommend buying from this shop?

We don’t only look at the price. We weigh different factors to find an offer that combines a good price, fast delivery and a reliable purchase.

  • Product price

    We calculate the total price you will pay and any discounts available from the shop.

  • Shipping & delivery time

    We check how quickly the product can be shipped and when you will receive it, based on your address.

  • Shop reliability

    We look at how often shops complete their orders successfully and how consistently they serve their customers.

  • Official reseller

    Where available, we take into account whether the shop is an official reseller of the brand.
What if it breaks?

You're covered by the statutory 2-year warranty. Contact us and we'll handle the entire process with the store, ensuring your issue is resolved with prompt support through a repair, replacement, or refund. Learn more

What if I change my mind?

No problem, as long as it's within 14 days. We'll come pick it up or you can choose the Skroutz Point that suits you, completely free for up to 2 times per year, and we'll refund your money. Get Skroutz Plus to enjoy unlimited free returns.

Learn more about invoicing

Reviews (2)

Reviews

5.0
2
5.0
Review this product
  1. 2
  2. 4 stars
    0
  3. 3 stars
    0
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews by our members

  • agagelis
    5
    5 out of 5 members found this review helpful
    agagelis

    Verified purchase

    Some of these specific boards, in some batches, have a problem that I saw being mentioned in various forums (https://www.mikrocontroller.net/topic/477142). To cut it short, the problem occurs if pin D12 makes contact with the ground (as shown by the green line). In this case, the board can be programmed normally but cannot connect to the network AT ALL!
    However, the solution is quite simple if you have the tools. The problem arises at the point where the yellow circle is shown. There is a factory-made hole there, which I opened slightly more (with a 1 mm drill and 1-2 turns by hand!!) and the problem was solved.
    CAUTION: Do not make the hole bigger than necessary!!! 1-2 turns are enough to scrape off the surface and remove the copper causing the short circuit, allowing the board to function. I hope I helped anyone facing a similar problem! Overall, the Board-aki works great (after the minor intervention, for which the Chinese factories are to blame!!), hence the 5 stars.

    Translated from Greek ·
    Did you find this review helpful?
  • 5
    Marios_Karathanasopoulos
    Expert user

    Verified purchase

  • agagelis
    5
    agagelis

    Some of these specific boards, in some batches, have a problem that I saw being mentioned in various forums (https://www.mikrocontroller.net/topic/477142). To cut it short, the problem occurs if pin D12 makes contact with the ground (as shown by the green line). In this case, the board can be programmed normally but cannot connect to the network AT ALL!
    However, the solution is quite simple if you have the tools. The problem arises at the point where the yellow circle is shown. There is a factory-made hole there, which I opened slightly more (with a 1 mm drill and 1-2 turns by hand!!) and the problem was solved.
    CAUTION: Do not make the hole bigger than necessary!!! 1-2 turns are enough to scrape off the surface and remove the copper causing the short circuit, allowing the board to function. I hope I helped anyone facing a similar problem! Overall, the Board-aki works great (after the minor intervention, for which the Chinese factories are to blame!!), hence the 5 stars.

    Translated from Greek ·
    5
  • 5
    Marios_Karathanasopoulos

    0
  • See all
Questions
Product report

Description & Specifications

The Optum ENC28J60 Ethernet shield connects an Arduino Nano board to the internet. It uses the Microchip ENC28J60 Ethernet controller and can operate as a server or client.

  • Type: Shield
  • Board model: Nano
  • Ethernet controller: Microchip ENC28J60
  • Operating mode: Server or client
  • Connection: Plugs directly into the board, no soldering required
  • Library and examples: Included

Manufacturer

Manufacturer Details

Warnings & Safety Information
Type
Shield
Board Model
Nano
Chipset
-

Important information

Specifications are collected from official manufacturer websites. Please verify the specifications before proceeding with your final purchase. If you notice any problem you can report it here.

Reviews (2)

5.0
2
5.0
Review this product
  1. 2
  2. 4 stars
    0
  3. 3 stars
    0
  4. 2 stars
    0
  5. 1 star
    0
Review this product

Reviews by our members

  • agagelis
    5
    5 out of 5 members found this review helpful
    agagelis

    Verified purchase

    Some of these specific boards, in some batches, have a problem that I saw being mentioned in various forums (https://www.mikrocontroller.net/topic/477142). To cut it short, the problem occurs if pin D12 makes contact with the ground (as shown by the green line). In this case, the board can be programmed normally but cannot connect to the network AT ALL!
    However, the solution is quite simple if you have the tools. The problem arises at the point where the yellow circle is shown. There is a factory-made hole there, which I opened slightly more (with a 1 mm drill and 1-2 turns by hand!!) and the problem was solved.
    CAUTION: Do not make the hole bigger than necessary!!! 1-2 turns are enough to scrape off the surface and remove the copper causing the short circuit, allowing the board to function. I hope I helped anyone facing a similar problem! Overall, the Board-aki works great (after the minor intervention, for which the Chinese factories are to blame!!), hence the 5 stars.

    Translated from Greek ·
    Did you find this review helpful?
  • 5
    Marios_Karathanasopoulos
    Expert user

    Verified purchase

  • agagelis
    5
    agagelis

    Some of these specific boards, in some batches, have a problem that I saw being mentioned in various forums (https://www.mikrocontroller.net/topic/477142). To cut it short, the problem occurs if pin D12 makes contact with the ground (as shown by the green line). In this case, the board can be programmed normally but cannot connect to the network AT ALL!
    However, the solution is quite simple if you have the tools. The problem arises at the point where the yellow circle is shown. There is a factory-made hole there, which I opened slightly more (with a 1 mm drill and 1-2 turns by hand!!) and the problem was solved.
    CAUTION: Do not make the hole bigger than necessary!!! 1-2 turns are enough to scrape off the surface and remove the copper causing the short circuit, allowing the board to function. I hope I helped anyone facing a similar problem! Overall, the Board-aki works great (after the minor intervention, for which the Chinese factories are to blame!!), hence the 5 stars.

    Translated from Greek ·
    5
  • 5
    Marios_Karathanasopoulos

    0
  • See all
17,36 €
4,50 €   shipping cost