Very good...

Reliable PLA for everyday prints, with consistent diameter and good bed adhesion. Works without issues on most printers and produces clean, uniform layers. The white color is quite “pure,” not yellowish. The quality is consistent for its price, although it does not reach premium brands. Very good choice for general use and large prints.

To avoid nightmares and panic:
1. Nozzle 0.6 ideally, at 0.4 and below it gets many clogs.
2. Load it with 210-220C nozzle temperature
3. Do a manual calibration to create a better filament profile
4. Use lower speeds if you want a good result

A real nightmare! The clogging was off the charts! For small prints where you can be present, everything is fine, very sturdy print and the wood hides many imperfections! It sands easily! But probably because you have to go up in nozzle diameter, you lose a lot of accuracy!! Imagine printing parts that need to fit together! Practically, you can't make threads, snap-fits, etc.! Drawers only on the condition that you sand them to fit afterwards! For small prints, the result was impressive! e.g. calibration cube, etc.!

It's good but it clogs immediately on a 0.2 nozzle.
On 0.4 and above there is no issue and it smells like burnt wood when printing

In color and texture it's 10/10, but because it's made of paper, probably when you want the measurement to be exact for a print it won't be, and you won't get the job done

It is not rainbow, just different colors that go in order

I bought it for Bambu Labs A1. I used filaments from Bambu Labs and found that this filament is clearly inferior to Bambu Labs'. It is not as smooth in texture, it slightly detached from the plate, and makes slight errors at the corners on flat surfaces. In some cases, it might be my fault, but I tried lowering speeds and temperature, dried it for a few hours, without a change in the result. For its price, it's definitely worth it when you don't care about 100% quality

I think it's fine for its price, I've seen detachments from the bed but generally it prints without issues

I used 2 spools on a Bambu P1S for printing large objects. Everything went perfectly with the default settings and the quality came out very good.

It is inferior quality plastic. For its price, it does an incredible job; the truth is that on the value for money scale, it gets 11/10, but I think it has now been surpassed in quality by several brands at a similar price. I prefer Sunlu or eSun for a few euros more. Strange finish, average overhangs, stringing (at 210, but come on, how low can you print it? You want flow too). The only super positive thing is its price; in all other measurements, it is average

Perfect material (PLA) for 3D printing! The quality/price ratio simply exceeds all expectations, I was hesitant seeing the price but in the end, it is authentic Creality3D PLA.

It doesn't mention in the description that it is cr-pla. It definitely requires 15% humidity and works well between 209-211 degrees

For its price, the filament is good. But for some reason, it constantly jams the printer nozzle. (I have tried 2 other brands where the plastic doesn't get stuck inside). I won't be absolute because it's plastic; maybe mine just came defective... But if you specifically want to leave the printer alone for hours to print without worrying that the nozzle will stop extruding plastic, I would suggest going for something more expensive.

Having used several spools on various printers, I can say that it is an excellent PLA for the price.

Very beautiful result, I have no complaints (yellow).

Very good filament. It took a little time to find the settings needed to avoid stringing, but after that, the 6 rolls I bought printed excellently.

It is what it says, PLA with wood powder. I didn't have any issues with printing at a speed of ~100mm/s. The printer needs to be very dry and properly calibrated for the first layer to come out right. It helps if you have textured PEI. It doesn't require a high temperature of ~195C. I printed it with a 0.5mm nozzle to avoid any chance of clogging due to the wood.

Excellent filament, tested on an Ender 3 V3 SE printer with a few parameter adjustments, the print is perfect

It took me a lot of testing to find the right settings, but the final product is worth it! I already bought extra packages.

I printed on an Ender 3 Pro and I would recommend:
45-50mm/s printing speed, 210-220 nozzle temperature. Definitely use a nozzle with a diameter of 0.5mm or larger, ideally hardened steel. The print will definitely have stringing, but it cleans up very easily.

Nice material, I tested it in trials/calibrations and ended up with 210/60 bed and I have nice quality and full speed in the 3D printer. I will buy again.

Difficult to use (I have previously used a wood filament from another brand without any issues). I don't know if it's the composition or the printer (ender 3v2) that's causing the problem, but I definitely won't be purchasing it again.

I am satisfied with the color and texture of the matte material. I did not encounter any issues during printing with this consumable